Acme Systems srl - Electronic design and manufacturing since 2005

Info Doc Buy

• CPU Microchip SAMA5D27
• Cortex A5 @ 500 MHz
• Armhf architecture
• DDR3L RAM 256 MB
• QuadSPI 0/16/64/128MB
• Size: 40x30 mm
• Plug-in module
• 200 pins 0.4 mm pitch
• TFT parallel interface
• Fully open source software
• Boot from internal Quad SPI or external uSD/eMMC
• Compatible with Debian, Yocto and Buildroot Linux distributions
• Linux mainstream up to version 5.4 LTS

Info Doc Buy

• CPU Microchip SAMA5D31/D36
• Cortex A5 @ 536 MHz
• Armhf architecture
• DDR2 RAM 256/512 MB
• Nand FLASH 0/256 MB
• On boar uSD socket
• Size: 53x53 mm
• Plug-in module
• 150 pins 1.27 mm pitch
• TFT parallel interface
• Fully open source software
• Boot from internal uSD/NAND flash or esternal eMMC
• Compatible with Debian, Yocto and Buildroot Linux distributions
• Linux mainstream up to version 5.4 LTS

Info Doc Buy

• CPU Microchip AT91SAMG25
• ARM9 @ 400 MHz
• Armel architecture
• DDR2 RAM 128/256 MB
• Size: 40x40 mm
• SMT module
• 96 pins 1.27 mm pitch
• Fully open source software
• Boot from external uSD or serial flash
• Compatible with Debian, Yocto and Buildroot Linux distributions
• Linux mainstream up to version 5.4 LTS

Info Doc Buy

• CPU Microchip AT91SAMG25
• ARM9 @ 400 MHz
• Armel architecture
• DDR2 RAM 128/256 MB
• Size: 53x25 mm
• Plug-in module
• 40 pins 2.54 mm pitch
• Fully open source software
• Boot from uSD
• Compatible with Debian, Yocto and Buildroot Linux distributions
• Linux mainstream up to version 5.4 LTS

Info Doc Buy

Raspberry CM3L+ 7 inch LCD panel

Thin and cheap 7 inch PC panel designed for the Raspberry Pi Compute Module 3+

• 800x480 pixel 7 inch TFT
• Socket for Raspberry Pi CM3L or CM3L+
• 10 points capacitive touch
• MIPI connector for Raspberry Pi Camera
• WiFi @ 2.4 GHz or USB port
• Operating temperature: -20° +70°

Info Doc Buy

Raspberry CM3L+ enhanced 7 inch LCD panel

Thin 7 inch PC panel designed for the Raspberry Pi Compute Module 3+

• 800x480 pixel 7 inch TFT
• Socket for Raspberry Pi CM3L or CM3L+
• 10 points capacitive touch
• MIPI connector for Raspberry Pi Camera
• WiFi @ 2.4 GHz or 5.8GHz (optional)
• Operating temperature: -20° +70°
• Ethernet POE
• 3 USB Host
• RS485 or RS232
• 1Relay
• Hi-quality audio out up 384KHz@32bit
• Filesystem safety power down
• RTC with backup battery

Info Doc Buy

Raspberry CM3L+ home controller

Home Automation carrier board designed for the Raspberry Pi Compute Module 3

• Socket for Raspberry Pi CM3L or CM3L+
• 2 USB 2.0 host port
• 1 Ethernet port at 10/100Mbit
• 1 Stereo audio out on 3.5 mm jack
• 1 Camera connector
• 1 Debug serial console port
• 1 Generic serial port
• 2 Low voltage relay
• 1 One-Wire bus
• 2 Opto-isolated dry contact inputs
• 2 Opto-isolated RS-485 bus
• 1 Seeedstudio Grove connector
• Socket for a bootable microSD
• Placement for a WiFi module @ 2.4GHz
• Placement for an IR receiver @ 38KHz
• Operating temperature: -20° +70°
• Power-in @ 12 to 24VDC

Info Buy

RGB led panel controller

HAT-A3 is the Acme Systems version of the Active-3 board designed by Henner Zeller to control a RGB led display with a standard Raspberry Pi3 or Pi4.

Acme Systems is proud to announce the begin of an exciting collaboration with Livio Argentini in development and manufacturing of professional pure analog audio equipments

Info

Strip led controller based on Espressif ESP-32 module

Info Doc Buy

Yarm is a smart and cost effective solution for system integrators to build their own RF applications at 868 MHz avoiding all the hardware design costs requested to start a new custom RF project.

Info Buy

Boris is a non-invasive, easy to install, inexpensive Battery Monitor System that can be attached to virtually every type of existing battery array like UPS or Solar Energy System.