Basic starter kit with all the hardware you need to get started with the FOX Board G20 Linux Embedded Single Board Computer

Parts

• a FOX Board G20
• a wall mounted power supply with 2 output at 5 Volt DC 500mA on USB port
• a DPI Debug Port Interface with USB cable
• a 2GB bootable microSD with preinstalled Debian Linux
• a Lithium backup battery for RTC circuitry model CR1220
• a FOXCASE-B black plastic enclosure

Please note that this hardware is not suggested for new projects because will be discontinued at the end of 2012

Parts included:

• FOX Board G20 with a set of of header 20x2 with pin length 6mm already soldered
• 2GB bootable microSD with preinstalled Debian Linux
• FOXGM2 carrier board
• modem Telit GM862-QUAD
• DPI interface and mini USB cable
• MMCX to FME cable (code MMCX2FME)
• GSM Antenna (code GSMANT)
• alluminium and plastic case specifically designed by Teko
• power supply with EU or US or UK or Australian AC plug

Please note that this hardware is not suggested for new projects because will be discontinued at the end of 2012

Parts included:

• FOX Board G20 with a set of of header 20x2 with pin length 6mm already soldered
• 2GB bootable microSD with preinstalled Debian Linux
• FOXGM2 carrier board
• Modem Telit GM862-GPS
• DPI interface and mini USB cable
• MMCX to FME cable (code MMCX2FME)
• MMCX to SMA cable (code MMCX2SMA)
• GSM Antenna (code GSMANT)
• GPS Antenna (code GPSANT)
• Alluminium and plastic case specifically designed by Teko
• Power supply with EU or US or UK or Australian AC plug

Minimal starter kit with the basic hardware you need to getting started with the BEE Board.

Hardware included:

• A BEE Board
• A wall mounted switching power supply at 5VDC-1A (PS-5V1A-EU-MUSB)
• A MiniUSB data cable

GSM/SMS application kit for BEE Board.

Hardware included:

• BEE Board
• Wall mounted switching power supply at 5VDC-1A (PS-5V1A-EU-MUSB)
• MiniUSB data cable
• DAISY-13 GPRS quad band Daisy module
• GSM rubber antenna
• 20cm daisy cable
• Screws and bolts

FOX Board G20 is a "ready-to-run" Embedded Linux System perfect to use as a solid state WEB server or as a core engine for your embedded appliances.

A fully Open Source environment is available to customize and build your own kernel image or to develop user applications using standard GNU tools. Version with Atmel AT91SAM9G20 with 256KB of FLASH memory, 64MB of RAM and up to 16GB of microSD.

FOXG20 needs some extra accessories in order to be operative:

• a bootable microSD with Linux OS (see DEBM2G or DEBM4G products)
• a 5 Volt DC power source (see PS5V1A product)
• a 3V lithium battery for internal RTC circuitry (see CH23-1220 product)

An evalution kit with all the accessories you need to get started with FOX Board G20 is available on-line on this link: COMBO-2.

Arduino compatible board with connectors to be wired to the Daisy board modules.

Colibri is a simple development board useful for evaluating the huge potentiality of the Actel ProASIC3 FPGA device model A3P250 with 250Kgates.

DPI is an USB to serial TTL converter at 3.3 volt useful to have access to the system messages generated by the FOX Board G20 on the debug port connector.

EPS is a DC-DC converter with an input range of 7 to 28 Volt DC output 5 Volt DC @ 2A.

Netus G20 is a 4x4cm Linux ready core engine based on the new ARM9 (c) CPU Atmel (tm) AT91SAM9G20 @ 400Mhz designed to reduce the time to market your Linux embedded projects.

• 256KB of data flash
• 64MB of RAM

Netus G20 is a 4x4cm Linux ready core engine based on the new ARM9 (c) CPU Atmel (tm) AT91SAM9G20 @ 400Mhz designed to reduce the time to market your Linux embedded projects.

• 8MB of serial flash
• 64MB of RAM

Power supply module that meets all the AT91SAM9G20 CPU power requirements and power-up and power-down sequences to guarantee reliable operations.

DAISY-1 is a pluggable adapter for the NETUSG20 module that provides 8 connectors compatible with the Acme Daisy Cabling System.

DAISY-2 is a bipolar stepper motor driver board (2.5A) based on Texas DRV8811 chip.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-4 is a single relay Daisy module.

Up to 8 Daisy-4 modules can be wired to a single Daisy flat cable.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-5 is simple module with 8 push buttons useful for lab experiments.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-9 is RS232 DTE serial interface, not optoisolated, with TXD, RXD, CTS and RTS signals.

Up to 6 DAISY-9 modules can be wired to a single DAISY-1 adapter.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-10 is an isolated RS485/RS422 interface.

Up to 3 DAISY-10 in RS485 mode can be wired on a DAISY-1 adapter for the FOXG20. Up to 6 modules in RS422 mode.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-11 is simple module with 8 leds useful for lab experiments.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-12 is a 40x40 mm prototyping board with daisy connector and small soldering area to make your daisy application.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-13 is a low power consumption, quad band, GPRS class 10 data module based on Teltonika TM1Q.

Note: The following components are not included. Don't forget to buy them to use this board:

• Daisy flat cable (code FC-19818-FF)
• GPS antenna rubber model (code:AN-GSM-RUBBER-SMA-M) or cable model (code: AN-GSM-CABLE-SMA-M)

GSM/GPRS Rubber Antenna for Daisy-13 module.

Features:

• Gain: 2dB
• Antenna length: 50 mm
• Connector: SMA R/A male
• Frequency: 850/1900MHz or 900/1900MHz
• Impedance: 50 Ohm

GSM/GPRS magnetic Antenna for Daisy-13 module with cable.

Features:

• Cable length: 2 meter
• Antenna height: 105 mm
• Connector: SMA R/A male
• Frequency: 850/1900MHz or 900/1900MHz
• Gain: 3dB

Daisy adapter for the 4Dsystems uLCD-32PT display

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

Audio adapter for FOX Board G20

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-18 is an opto-isolated 0-48 volt 4ch input for industrial purposes.

Up to 4 DAISY-18 can be wired on a DAISY-1 adapter for the NETUSG20.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

DAISY-19 is an opto-isolated 0-48 volt solid state 4ch switch for industrial purposes.

Up to 4 DAISY-19 can be wired on a DAISY-1 adapter for the NETUSG20.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

Front-end for the 4 channel A/D 10bits converter built-in the CPU AT91SAM9G20.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

This board is based on a PCF8574 chip, a 8-bit quasi-bidirectional port and an I2C-bus interface with low current consumption and latched outputs with high current drive capability for directly driving LEDs.

Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF)

20 cm ribbon cable with 10 wires compatible with the Acme Daisy Cabling System.

At least one of these cables is required to connect each Daisy module.

if you need different lengths please consider making your own the cable using the IDC socket JJ-02291-10P-F and the flat cable FC-3754-1M.

IDC connector with 1.27mm spaced dual-row pin headers. The insulation displacement (IDC) contacts on these connectors allow them to be quickly and easily crimped onto FC-3754 flat ribbon cable for Daisy cabling system.

This female socket is designed to be connected to the male header on the Daisy modules. A polarizing tab in the middle ensures the correct orientation.

4U connector datasheet

1 meter of grey conductor flat cable, .025" pitch, 10 wires at 30 AWG, to use for Daisy wiring.

| 3M Datasheet |

The EZL-176 is a compact and cost effective all-in-one SMART serial TFT display module. THe EZL-176 has 1,76 inch diagonal and 176x220 resolution, and embedded GOLDELOX-SGC graphics controller that delivers “stand-alone” functionality to any project.

| More info... |

SGC serial command version of the 4D Systems uLCD-32PT.

• 3.2 inch LCD TFT
• Touch panel
• 240x320 pixel
• 65K colors
• Picaso graphic processor.

Wireable to the Daisy Cabling Systems using a DAISY-15 adapter.

FOX size prototyping board.

Eurocard size (160x100 mm) prototyping board 2.54 mm pitch for FOX Board G20 or FOX Board LX832.

Small breadboard with 170 tie points. Self-adhesive backing. Measures 45mm x 25mm (1.8"x 1.4").

IDC connector with 1.27mm spaced dual-row pin headers. The insulation displacement (IDC) contacts on these connectors allow them to be quickly and easily crimped onto FC-3754 flat ribbon cable for Daisy cabling system.

This female socket is designed to be connected to the male header on the Daisy modules. A polarizing tab in the middle ensures the correct orientation.

| 4U connector datasheet |

FOXCASE is a transparent plastic enclosure for the FOX Board G20.

FOXCASE is a black plastic enclosure for the FOX Board G20.

Plastic case for the FOX Board G20 that resembles the very popular Linux icon TUX drawn by Larry Ewing.

Bootable 2GB microSD Memory with a preinstalled Debian Linux distribution for the FOX Board G20.

Warning: Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.

Bootable 4GB microSD Memory with a preinstalled Debian Linux distribution for the FOX Board G20.

Warning: Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.

Blank 2GB microSD memory card compatible with FOX Board G20.

Blank 4GB microSD memory card compatible with FOX Board G20.

Blank 16GB microSD memory card compatible with FOX Board G20.

USB 2.0 microSD reader. Supports Micro SD HC and M2 Card

• Ideal for hi-fi systems and car radios with USB Memory player feature
• Compatible with Windows, Mac and Linux
• Data transfer rate up to 480Mbps USB 2.0

• Q.ty 6 of 2x20 header pitch 2.54mm L 6mm
• Q.ty 6 of 2x20 header pitch 2.54mm L 12mm
• Q.ty 6 of 2x20 socket pitch 2.54mm

One Female and one Male connector at 60 pin 0.8mm pitch for Netus G20 carrier boards placement. For production batch this product is available in reel of 1000 pcs. Please contact us to have a quote.

Features

• European AC input: 100-240VAC 50/60Hz 0.2A
• DC output: 2 USB power out plug. Output 1: 5VDC/500mA, output 2: 5VDC/500mA
• Pluggable directly to the FOX Board with the included USB to 3.5 DC cable

Features

• US AC input: 100-240VAC 50/60Hz 0.2A
• DC output: 2 USB power out plug. Output 1: 5VDC/500mA, output 2: 5VDC/500mA
• Pluggable directly to the FOX Board with the included USB to 3.5 DC cable

Features

• United Kingdom AC input: 100-240VAC 50/60Hz 0.2A
• DC output: 2 USB power out plug. Output 1: 5VDC/500mA, output 2: 5VDC/500mA
• Pluggable directly to the FOX Board with the included USB to 3.5 DC cable

Features

• Australian AC input: 100-240VAC 50/60Hz 0.2A
• DC output: 2 USB power out plug. Output 1: 5VDC/500mA, output 2: 5VDC/500mA
• Pluggable directly to the FOX Board with the included USB to 3.5 DC cable

Switching power supply for FOX Board G20 with AC plug for US

• Input 100-240VAC 50/60Hz
• Output 5VDC/1A
• Pluggable directly to the FOX Board LX or G20

Provided with US AC plug

Switching power supply for Bee Board with AC plug for EU

• Input 100-240VAC 50/60Hz
• Output 5VDC/1A
• Pluggable directly to the Bee Board

Provided with EU AC plug

EPS is a DC-DC converter with an input range of 7 to 28 Volt DC output 5 Volt DC @ 2A.

Power supply module that meets all the AT91SAM9G20 CPU power requirements and power-up and power-down sequences to guarantee reliable operations.

Lithium battery model CR1220 at 3 volt for the FOX Board G20 RTC circuitry.

DS18B20 is a digital thermometer provides 9-bit to 12-bit Celsius temperature measurements.

Shipped with a 4.7 KOhm resistor.

| Use it with the FOX Board G20 |

Microsoft LifeCam HD-3000 webcam

| Microsoft description... | How to use it with FOXG20 |

Microsoft LifeCam HD-5000 webcam

Microsoft description... | How to use it with FOXG20

D-Link USB WiFi mini adapter.

The packaging could be different than in photo.

Use it with FOXG20 | Product info

TP-Link wi-fi adapter with high gain antenna

Use it with teh FOX Board G20

The Bluetooth USB adapter allows you to connect with your FOX Board enabled Bluetooth device such as Mobile, PC, PDA, and so on. It is Bluetooth 2.0 + EDR compliant and offers a transmission range up to 20 meter in open space.

The packaging could be different from the photo.

More info

GPS antenna with SMA male connector to to use with MMCX2SMA cable.

Cable lenght: 5 mt