Linux SoM
This is the catalog of all the Daisy add-on module available.
 | DAISY-3 is led based logic line state monitor useful to check the logic state of any daisy line Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | Daisy-7 is a 9 Degrees of Freedom module (9DOF) with digital MEMS (accelerometer, gyroscope, compass, barometer) and a GPS receiver IC in just 4x4cm. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | GPS antenna with SMA male connector to use Daisy-7 add-on board.
|
 | DAISY-8 is a 2 relay and 2 input interface for Terra and FOX Board Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-10 is an isolated RS485/RS422 interface. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-9 is RS232 DTE serial interface, not optoisolated, with TXD, RXD, CTS and RTS signals. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-18 is an opto-isolated 0-48 volt 4ch input for industrial purposes. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-19 is an opto-isolated 0-48 volt solid state 4ch switch for industrial purposes. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | Front-end for the 4 channel A/D 10bits converter built-in the Atmel CPU. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | Daisy-24 mini alphanumeric I2C 16x2 characters LCD module with 4 push buttons. Usable as Terra Board front panel or as normal Daisy module for other board with Daisy connectors.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM). It is not needed if you plug
it directly on a Terra board. |
 | DAISY-4 is a single relay Daisy module. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-1 is a pluggable adapter for the NETUSG20 module that provides 8 connectors compatible with the Acme Daisy Cabling System. | More info... | |
 | DAISY-2 is a bipolar stepper motor driver board (2.5A) based on Texas DRV8811 chip. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FC-19818-FF) EOL product. Last few pcs available. This product will be replaced very soon with a newer version. E-mail us for more info |
 | DAISY-5 is simple module with 8 push buttons useful for lab experiments. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-11 is simple module with 8 leds useful for lab experiments. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | DAISY-12 is a 40x40 mm prototyping board with daisy IDC connector mounted and small soldering area to create your custom daisy add-on module. Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | 4D Systems LCD display model uLCD-32PTU
Wireable to the Daisy Cabling Systems using a DAISY-15-R adapter. |
 | Daisy adapter for LCD-3 display (4Dsystems ULCD-32PTU) Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | End Of Life products. Don't use it new projects. Use the uLCD-32PTU model (Acme code: LCD-3) instead of it
4D Systems LCD display model uLCD-32PT
Wireable to the Daisy Cabling Systems using a DAISY-15 adapter. | More info... | |
 | Daisy adapter for the 4Dsystems uLCD-32PT display Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) |
 | Audio adapter for FOX Board G20 Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM) | More info... | |
 | 20 cm ribbon cable with 10 wires compatible with the Acme Daisy Cabling System. At least one of these cables is required to connect each Daisy module. if you need different lengths please consider making your own the cable using the IDC socket JJ-02291-10P-F and the flat cable FC-3754-1M. |
 | IDC connector with 1.27mm spaced dual-row pin headers. The insulation displacement (IDC) contacts on these connectors allow them to be quickly and easily crimped onto FLAT-20CM flat ribbon cable for Daisy cabling system. This female socket is designed to be connected to the male header on the Daisy modules. A polarizing tab in the middle ensures the correct orientation. | Datasheet | |
 | Daisy IDC male SMT connector for PCB mounting | Datasheet | |
 | 1 meter of grey conductor flat cable, .025" pitch, 10 wires at 30 AWG, to use for Daisy wiring. | 3M Datasheet | |
 | Set of 100 screws M2 length 4mm for daisy modules:
|
 | Set of 1000 screws M2 length 4mm for daisy modules:
|
 | Pack of 4 pcs of M2 spacer height 5 mm with metric thread internal to use with the screws M2X4 to mount the daisy module on a base panel. |
|
|
Atmel© Certified Partner |
Documentation Terms of Use
Acme Systems provides this documentation "as is" without warranty or guarantees of any kind.
The mantainer of this site (Sergio Tanzilli), has gone to a great deal
of effort into making this documentation as correct as possible.
Acme Systems doesn't provide any direct support for the Open Source preinstalled software but provides, through
these pages and forum posts, all the information required to obtain the sources, install, use and update the
Open Source softwares runnable on the FOX Board, NetusG20, AriaG25 and Terra platforms.
Please note that all the preinstalled softwares, used on the Acme Systems products, are Open Source and you will
have to check the license terms provided (usually the GPL) by each author before using it in any commercial or non-commercial
product, by yourself.
Before sending emails or calling the Acme staff here are our contacts
please note that WE ARE MAINLY HARDWARE DESIGNERS and NOT LINUX GURUS so could be better to post
your questions directly to the forum listed below to be sure that all the contributors of this site and
the large software developers community will read and reply to your questions.
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 3.0 Unported License.
