ACQUA-256E EUR 49.00
| ACQUA-256E - SAMA5D31 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D31 MPU
- 256 MByte of RAM
- No NAND flash memory
- Extended temperature range (-25° +85°)
| Product description | |
| SAMA5D31 System on module - ext temp range | 49,00 |
ACQUA-256E-N256 EUR 52.00
| ACQUA-256E-N256 - SAMA5D31 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip with:
- Atmel SAMA5D31 MPU
- 256 MByte of RAM
- 256MByte of NAND flash memory
- Extended temperature range (-25° +85°)
| Product description | |
| SAMA5D31 System on module - ext temp range | 52,00 |
ACQUA-256E-N256-D36 EUR 58.00
| ACQUA-256E-N256-D36 - SAMA5D36 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip with:
- Atmel SAMA5D36 MPU
- 256 MByte of RAM
- 256MByte of NAND flash memory
- Extended temperature range (-25° +85°)
- CAN Bus
| Product description | |
| SAMA5D36 System on module - ext temp range | 58,00 |
ACQUA-512 EUR 58.00
| ACQUA-512 - SAMA5D31 System on module Acqua A5 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D31 MPU
- 512 MByte of RAM
- No NAND flash memory
- Commercial Temperature range (0° +70°)
| Product description | |
| SAMA5D31 System on module | 58,00 |
ACQUA-512-N256 EUR 61.00
| ACQUA-512-N256 - SAMA5D31 System on module Acqua A5 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D31 MPU
- 512 MByte of RAM
- 256MByte of NAND flash memory
- Commercial temperature range (-0° +70°)
| Product description | |
| SAMA5D31 System on module | 61,00 |
ACQUA-512E EUR 66.00
| ACQUA-512E - SAMA5D31 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D31 MPU
- 512 MByte of RAM
- No NAND flash memory
- Extended temperature range (-25° +85°)
| Product description | |
| SAMA5D31 System on module - ext temp range | 66,00 |
ACQUA-512E-N256 EUR 69.00
| ACQUA-512E-N256 - SAMA5D31 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D31 MPU
- 512 MByte of RAM
- 256MByte of NAND flash memory
- Extended temperature range (-25° +85°)
| Product description | |
| SAMA5D31 System on module - ext temp range | 69,00 |
ACQUA-512E-N256-D36 EUR 75.00
| ACQUA-512E-N256-D36 - SAMA5D36 System on module - ext temp range Acqua A5 is a small and low-cost Linux embedded system on chip with:
- Atmel SAMA5D36 MPU
- 512 MByte of RAM
- 256 MByte of NAND flash memory
- Extended temperature range (-25° +85°)
- CAN Bus
| Product description | |
| SAMA5D36 System on module - ext temp range | 75,00 |
AN-GSM-CABLE-SMA-M EUR 8.00
| AN-GSM-CABLE-SMA-M - GSM 2m cable antenna GSM/GPRS magnetic Antenna for TERRA-M board with cable.
Features:
- Cable length: 2 meter
- Antenna height: 105 mm
- Connector: SMA R/A male
- Frequency: 850/1900MHz or 900/1900MHz
- Gain: 3dB
|
| GSM 2m cable antenna | 8,00 |
AN-GSM-RUBBER-SMA-M EUR 6.00
| AN-GSM-RUBBER-SMA-M - GSM rubber antenna GSM/GPRS Rubber Antenna for TERRA-M board or DAISY-31 M-Bus adapter.
Features:
- Gain: 2dB
- Antenna length: 50 mm
- Connector: SMA R/A male
- Frequency: 850/1900MHz or 900/1900MHz
- Impedance: 50 Ohm
|
| GSM rubber antenna | 6,00 |
AN-WIFI-01 EUR 3.50
| AN-WIFI-01 - WiFi pcb external antenna WiFi PCB antenna with 11 cm cable and UMC 2mm connector to be plugged on WIFI-2 module.
| Antenna datasheet |
|
| WiFi pcb external antenna | 3,50 |
AN-WIFI-02 EUR 7.00
| AN-WIFI-02 - WiFi external antenna with SMA cable (Version FEMALE/MALE) Antenna for WIFI-2 module
- Rubber antenna with FEMALE SMA connector
- RF cable with panel mountable MALE SMA connector and 2mm UMC connector with about 10 cm length cable
| Antenna datasheet | Cable datasheet |
|
| WiFi external antenna with SMA cable (Version FEMALE/MALE) | 7,00 |
AN-WIFI-03 EUR 7.00
| AN-WIFI-03 - WiFi external antenna with SMA cable (Version MALE/FEMALE) Antenna for WIFI-2 module
- Rubber antenna with MALE SMA connector
- RF cable with panel mountable FEMALE SMA connector and 2mm UMC connector with about 10 cm length cable
| Antenna datasheet | Cable datasheet |
|
| WiFi external antenna with SMA cable (Version MALE/FEMALE) | 7,00 |
ARIAG25-128 EUR 27.60
| ARIAG25-128 - ARM9 Linux Embedded Module Aria G25 is a small and low-cost multi-chip module that integrates:* an ARM9 @ 400Mhz CPU Atmel AT91SAM9G25* a 128MB of DDR2 RAM* 10/100 Ethernet interface* up to 3 USB 2.0 host ports* Normal temperature range version (-0° +70°)
| Product description | |
| ARM9 Linux Embedded Module | 27,60 |
ARIAG25-128-E EUR 33.35
| ARIAG25-128-E - ARM9 Linux Embedded Module - extended range Aria G25 is a small and low-cost multi-chip module that integrates:* an ARM9 @ 400Mhz CPU Atmel AT91SAM9G25* a 128MB of DDR2 RAM* 10/100 Ethernet interface* up to 3 USB 2.0 host ports* Extended temperature range version (-20° +70°)
| Product description | |
| ARM9 Linux Embedded Module - extended range | 33,35 |
ARIAG25-256 EUR 33.35
| ARIAG25-256 - ARM9 Linux Embedded Module Aria G25 is a small and low-cost multi-chip module that integrates:* an ARM9 @ 400Mhz CPU Atmel AT91SAM9G25* a 256MB of DDR2 RAM* 10/100 Ethernet interface* up to 3 USB 2.0 host ports* Normal temperature range version (-0° +70°)
| Product description | |
| ARM9 Linux Embedded Module | 33,35 |
ARIAG25-256-E EUR 39.10
| ARIAG25-256-E - ARM9 Linux Embedded Module - extended range Aria G25 is a small and low-cost multi-chip module that integrates:* an ARM9 @ 400Mhz CPU Atmel AT91SAM9G25* a 256MB of DDR2 RAM* 10/100 Ethernet interface* up to 3 USB 2.0 host ports* Extended temperature range version (-20° +70°)
| Product description | |
| ARM9 Linux Embedded Module - extended range | 39,10 |
ARIETTA-G25-256-V EUR 30.00
| ARIETTA-G25-256-V - ARM9 Linux Embedded Module (Green,256MB) Arietta G25 is a small and low-cost multi-chip module that integrates:
- a ARM9 @ 400Mhz CPU Atmel AT91SAM9G25
- a 256MB of DDR2 RAM
- up to 3 USB 2.0 host ports
- 20x2 pads for strip pitch 2.54mm (100mil)
Basic Version with no strips mounted. If you need to have any strip mounted take a look to the soldering services
Starting from July 2018 we make by default just color green Arietta G25. The only difference between the legacy black version and the new green version is the solder mask color.
To order the legacy black version (Product id: ARIETTA-G25-256, MOQ 100 pcs) please contact us
| Product description | |
| ARM9 Linux Embedded Module (Green,256MB) | 30,00 |
ARIETTA-G25-V EUR 25.00
| ARIETTA-G25-V - ARM9 Linux Embedded Module (Green,128MB) Arietta G25 is a small and low-cost multi-chip module that integrates:
- a ARM9 @ 400Mhz CPU Atmel AT91SAM9G25
- a 128MB of DDR2 RAM
- up to 3 USB 2.0 host ports
- 20x2 pads for strip pitch 2.54mm (100mil)
- Solder mask color: green
Basic Version with no strips mounted. If you need to have any strip mounted take a look to the soldering services
Starting from July 2018 we make by default just color green Arietta G25. The only difference between the legacy black version and the new green version is the solder mask color.
To order the legacy black version (Product id: ARIETTA-G25, MOQ 100 pcs) please contact us
| Product description | |
| ARM9 Linux Embedded Module (Green,128MB) | 25,00 |
ATMEL-ICE-BASIC EUR 80.00
| ATMEL-ICE-BASIC - Microchip (Atmel) JTAG programmer Atmel-ICE is a powerful development tool for debugging and programming
ARM® Cortex®-M based Atmel® SAM and Atmel AVR® microcontrollers with On-Chip Debug capability
| How to use it | |
| Microchip (Atmel) JTAG programmer | 80,00 |
BAT-HOLDER-1 EUR 1.00
| BAT-HOLDER-1 - Battery holder for lithium battery CR1220 Battery holder for lithium battery CR1220. Through hole mount.
|
| Battery holder for lithium battery CR1220 | 1,00 |
BAT-HOLDER-2 EUR 1.00
| BAT-HOLDER-2 - Battery holder for lithium battery CR1220 Battery holder for lithium battery CR1220. SMT mount.
|
| Battery holder for lithium battery CR1220 | 1,00 |
BERTA-A5-BASIC EUR 9.00
| BERTA-A5-BASIC - Breakout board for Acqua A5 Breakout board for Acqua A5 SoM
| Product description | |
| Breakout board for Acqua A5 | 9,00 |
BERTA-A5-EXT EUR 25.00
| BERTA-A5-EXT - Breakout board for Acqua A5 with connectors Breakout board for Acqua A5 SoM with power supply section, ethernet and USB connectors.
| Product description | |
| Breakout board for Acqua A5 with connectors | 25,00 |
BERTA-D2 EUR 30.00
| BERTA-D2 - Basic evaluation board for RoadRunner SOM Basic evaluation board for RoadRunner SOM:
- RoadRunner not included
- MicroSD not included
| Product description | |
| Basic evaluation board for RoadRunner SOM | 30,00 |
BERTA-G25 EUR 74.00
| BERTA-G25 - Evaluation board for Aria G25 Mounted version of BERTA, the basic evaluation board for Aria G25 module:
- Aria G25 module with 256MB of RAM (ARIAG25-256)
- PS3V3 USB power supply module
- Double USB host connector
- SD card holder
- Vertical microSD card holder
- LAN connector
- Winstar I2C 16x2 alphanumeric LCD with backlight
- Debug port pins
- Bootable microSD card
- Wall power adapter
The Aria G25 il welded so it can't be removed from the board for further purposes.
| Product description | |
| Evaluation board for Aria G25 | 74,00 |
BERTA-PCB EUR 12.00
| BERTA-PCB - Prototyping board for AriaG25 SoM PCB of the prototyping board for AriaG25
| Product description | |
| Prototyping board for AriaG25 SoM | 12,00 |
CABLE-01 EUR 1.50
| CABLE-01 - Mini USB data cable Mini USB data cable
- Length 80 cm
- Compatible with:
|
| Mini USB data cable | 1,50 |
CABLE-02 EUR 1.50
| CABLE-02 - Micro USB data cable Micro USB data cable
- Compatible with:
- Length: about 1mt
|
| Micro USB data cable | 1,50 |
CABLE-03 EUR 1.00
| CABLE-03 - Flat data cable (16 wires) Flat data cable
- Length: about 15cm
- 16 wires
- Female to female
|
| Flat data cable (16 wires) | 1,00 |
CABLE-04 EUR 1.00
| CABLE-04 - Power cable for LED panel Power cable for RGB Ledpanel
|
| Power cable for LED panel | 1,00 |
CABLE-05 EUR 4.20
| CABLE-05 - HDMI cable 0.5 mt
- Connector 1: HDMI type A male
- Connector 2: HDMI type A male
- Legth: 0.5 mt
|
| HDMI cable 0.5 mt | 4,20 |
CABLE-06 EUR 1.20
| CABLE-06 - Ethernet cable 0.5 mt
- Lenght 0.5 mt
- Flat
- Color black
|
| Ethernet cable 0.5 mt | 1,20 |
CAM-5MP EUR 9.00
| CAM-5MP - Raspberry Pi camera module 5MP 1080p ver 1.3
- Fully compatible with CM3-Panel, CM3-Home and Raspberry Pi 3 A+ and B+
- 5MP Omnivision 5647 camera module
- Still picture resolution: 2592 x 1944
- Video: supports 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 recording
- 15-pin MIPI camera serial interface
- Plugs directly into the CM3-Panel, CM3-Home and Raspberry Pi 3 A+ and B+ MIPI connector
- Size: 20 x 25 x 9mm
- Weight: 3g
- Fully compatible with many Raspberry Pi cases
|
| Raspberry Pi camera module 5MP 1080p ver 1.3 | 9,00 |
CH23-1220 EUR 3.00
| CH23-1220 - 3V Lithium battery Lithium battery model CR1220 at 3 volt for RTC circuitry on:
|
| 3V Lithium battery | 3,00 |
CM3-HOME-B EUR 120.00
| CM3-HOME-B - Home automation carrier board for Raspberry CM3L+ module Motherboard designed to provide a reliable Home Automation solution based on Raspberry Pi CM3LPLUS industrial module
Please note: This code is related just to the carrier board. The Raspberry CM3L+ module is not included
Optional parts:
- CM3L+ - Raspberry Compute Module (Product CM3L+)
- CM3-HOME-CASE Plastic enclusure (Product CM3-HOME-CASE)
- MICROSD8G-E MicroSD
- WIFI-2 Wifi module
- AN-WIFI-01 or AN-WIFI-01 WiFi antennas
| Product description || CM3-Home catalog | |
| Home automation carrier board for Raspberry CM3L+ module | 120,00 |
CM3-HOME-CASE EUR 8.00
| CM3-HOME-CASE - DIN rail case for CM3-HOME board Enclosure for CM3-HOME board
|
| DIN rail case for CM3-HOME board | 8,00 |
CM3-PANEL-7-POE EUR 195.00
| CM3-PANEL-7-POE - Raspberry CM3+ 7 inch LCD panel with POE CM3-PANEL-7-POE is an enhanced version of popular CM3-PANEL with a large set of interfaces
Product available on January 2021
Main features
Included
Not Included
- MicroSD
- WiFi module
- Power supply
- Case
| Product description | |
| Raspberry CM3+ 7 inch LCD panel with POE | 195,00 |
CM3-PANEL-U EUR 95.00
| CM3-PANEL-U - Panel PC (USB version) with Raspberry Pi CM3L module
Panel PC carrier board for Raspberry Pi compute module 3 that includes:
- CM3-PANEL carrier board
- A 7 inch TFT LCD with 10 points capacitive touch
- Raspberry PI CM3L compute module
- USB 2.0 host port
The MicroSD is not provided
| Product description | |
| Panel PC (USB version) with Raspberry Pi CM3L module | 95,00 |
CM3-PANEL-UE EUR 71.00
| CM3-PANEL-UE - Panel PC (USB version)
Panel PC carrier board for Raspberry Pi compute module 3 that includes:
- CM3-PANEL carrier board
- A 7 inch TFT LCD with 10 points capacitive touch
- An USB 2.0 host port
The Raspberry Pi compute module 3 is not provided
The MicroSD is not provided
| Product description | |
| Panel PC (USB version) | 71,00 |
CM3-PANEL-W EUR 99.00
| CM3-PANEL-W - Panel PC (WiFi version) with Raspberry Pi CM3L module
Panel PC carrier board for Raspberry Pi compute module 3 that includes:
- CM3-PANEL carrier board
- A 7 inch TFT LCD with 10 points capacitive touch
- Raspberry PI CM3L compute module
- A WiFi module @ 2.4 GHz
- PCB antenna
The MicroSD is not provided
| Product description | |
| Panel PC (WiFi version) with Raspberry Pi CM3L module | 99,00 |
CM3-PANEL-WE EUR 75.00
| CM3-PANEL-WE - Panel PC (WiFi version)
Panel PC carrier board for Raspberry Pi compute module 3 that includes:
- CM3-PANEL carrier board
- 7 inch TFT LCD with 10 points capacitive touch
- WiFi module @ 2.4 GHz
- PCB antenna
The Raspberry Pi compute module 3 is not provided
The MicroSD is not provided
| Product description | |
| Panel PC (WiFi version) | 75,00 |
CM3LPLUS EUR 26.00
| CM3LPLUS - Raspberry Compute Module 3 plus lite edition (no eMMC) Raspberry Pi Compute Module versione 3+ for CM3-Home
Version without eMMC memory.
| CM3-Home || Product description | |
| Raspberry Compute Module 3 plus lite edition (no eMMC) | 26,00 |
COMBO-100 EUR 65.00
| COMBO-100 - Arietta G25 evaluation kit Basic kit to evaluate the Arietta G25 SOM
Parts included:
- ARIETTA-G25-256-V (256MB of RAM)
- WIFI-2 WiFi module (mounted) with PCB antenna
- Bootable microSD with Debian Linux preinstalled
- Debug port interface + CABLE-01 mini USB data cable
- PS5V1A-USB2 Wall adapter + CABLE-02 Micro USB power cable
- 6 pins male connector mounted on DPI port
- 20+20 pins male connector (unmounted)
- 20+20 pins female connector (unmounted)
|
| Arietta G25 evaluation kit | 65,00 |
COMBO-2 EUR 159.00
| COMBO-2 - FOX Board G20 combo box Basic starter kit with all the hardware you need to get started with the FOX Board G20
Linux Embedded Single Board Computer
Parts included:
- One FOX Board G20 (Code FOXG20)
- One wall mounted power supply with 2 output at 5 Volt DC 500mA on USB port
- One USB to 3.3 volt serial interface (Code USB-3V-SER)
- A bootable microSD with preinstalled Debian Linux
- One Lithium backup battery for RTC circuitry model CR1220 (Code CH23-1220)
- One FOXCASE-B black plastic enclosure (Code FOXCASE-B)
| Product description | FOX Board G20 catalog |
|
| FOX Board G20 combo box | 159,00 |
COMBO-M2 EUR 369.00
| COMBO-M2 - TERRA-M GPRS Legacy Terra-M board + accessories
Parts included:
- One TERRA-M Board (Code TERRA)
- A bootable microSD with Debian Linux preinstalled
- One Debug port interface (Code DPI)
- One USB data cable for DPI
- One wall adapter 12 volt @ 2A switching power supply (Code PS12V2A-EU)
- One Teko Tekal enclosure
- One Daisy-24 lcd module
- One Lithium battery model CR1220 at 3 volt for RTC circuitry (Code CH23-1220)
- GSM antenna with 2 mt cable
| Product description | Terra catalog
|
| TERRA-M GPRS | 369,00 |
CON-01 EUR 3.00
| CON-01 - DVI-D to HDMI adapter
- Connector 1: DVI-D, (18+1), plug
- Connector 2: HDMI type A, jack
- Cable type: Single-Link
- HDTV Standard: 1080p
- HDTV Resolution max.: 2560 x 1600 Pixel, 60Hz
- Hoods: molded
- Shielding: single shielding
- Connector surface: nickel-plated
- Color connector: black
| datasheet |
|
| DVI-D to HDMI adapter | 3,00 |
DAISY-12 EUR 3.00
| DAISY-12 - Prototyping board DAISY-12 is a 40x40 mm prototyping board with daisy IDC connector mounted and small soldering area to create your custom daisy add-on module.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | Daisy catalog |
|
| Prototyping board | 3,00 |
DAISY-18 EUR 14.00
| DAISY-18 - 4 channel industrial range optoisolated input (0-48 volt) DAISY-18 is an opto-isolated 0-48 volt 4ch input for industrial purposes.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | |
| 4 channel industrial range optoisolated input (0-48 volt) | 14,00 |
DAISY-19 EUR 14.00
| DAISY-19 - 4 channel industrial range optoisolated output (0-48 volt) DAISY-19 is an opto-isolated 0-48 volt solid state 4ch switch for industrial purposes.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | Daisy catalog |
|
| 4 channel industrial range optoisolated output (0-48 volt) | 14,00 |
DAISY-20 EUR 8.00
| DAISY-20 - 4 ch 0-10 volt A/D interface Front-end for the 4 channel A/D 10bits converter built-in the Atmel CPU.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | Daisy catalog |
|
| 4 ch 0-10 volt A/D interface | 8,00 |
DAISY-30 EUR 2.00
| DAISY-30 - Adapter for XBee modules Daisy to XBee module adapter
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | Daisy catalog |
|
| Adapter for XBee modules | 2,00 |
DAISY-5 EUR 5.00
| DAISY-5 - 8 push buttons daisy module DAISY-5 is simple module with 8 push buttons useful for lab experiments.
Note: the daisy flat cable to wire this board is not included. Don't forget to buy it (code FLAT-20CM)
| Product description | Daisy catalog |
|
| 8 push buttons daisy module | 5,00 |
DEBM8G-E-ACQUA EUR 20.00
| DEBM8G-E-ACQUA - Debian microSD 8GB industrial grade for Acqua A5 Bootable 8GB microSD with a preinstalled Debian Linux distribution for Acqua A5 board.
- Class 10 HC
- Temperature range: -25° to +85°
Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.
| Product description |
|
| Debian microSD 8GB industrial grade for Acqua A5 | 20,00 |
DEBM8G-E-ARIA EUR 20.00
| DEBM8G-E-ARIA - Debian microSD 8GB industrial grade for Aria G25 Bootable 8GB microSD with a preinstalled Debian Linux distribution for Aria G25 board.
- Class 10 HC
- Temperature range: -25° to +85°
Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.
| Product description |
|
| Debian microSD 8GB industrial grade for Aria G25 | 20,00 |
DEBM8G-E-ARIETTA EUR 20.00
| DEBM8G-E-ARIETTA - Debian microSD 8GB industrial grade for Arietta G25 Bootable 8GB microSD with a preinstalled Debian Linux distribution for Arietta G25 board.
- Class 10 HC
- Temperature range: -25° to +85°
Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.
| Product description |
|
| Debian microSD 8GB industrial grade for Arietta G25 | 20,00 |
DEBM8G-E-FOX EUR 20.00
| DEBM8G-E-FOX - Debian microSD 8GB industrial grade for FOX Board G20 Bootable 8GB microSD with a preinstalled Debian Linux distribution for FOX Board G20.
- Class 10 HC
- Temperature range: -25° to +85°
Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.
| Product description |
|
| Debian microSD 8GB industrial grade for FOX Board G20 | 20,00 |
DEBM8G-E-RR EUR 20.00
| DEBM8G-E-RR - Debian microSD 8GB industrial grade for RoadRunner Bootable 8GB microSD with a preinstalled Debian Linux distribution for RoadRunner SOM.
- Class 10 HC
- Temperature range: -25° to +85°
Please note that this card contains Open Source code under GPL licence and you are buying just the memory card not the software on it. Any rights on this software or support are not included.
| Product description |
|
| Debian microSD 8GB industrial grade for RoadRunner | 20,00 |
DPI EUR 8.00
| DPI - Debug Port Interface DPI is an USB-to-serial interface to link the Acme boards debug port to a PC USB host port and have access at the Linux system console using a terminal emulator program like minicom, putty, hyperterminal, etc.
| Product description | |
| Debug Port Interface | 8,00 |
DS18B20 EUR 5.00
| DS18B20 - 1-wire Dallas DS18B20 thermal sensor The Dallas/Maxim DS18B20 is a 1-wire digital thermometer:
- Measures Temperatures from -55°C to +125°C (-67°F to +257°F)
- ±0.5°C Accuracy from -10°C to +85°C
- Programmable Resolution from 9 Bits to 12 Bits
- Each Device Has a Unique 64-Bit Serial Code Stored in On-Board ROM
| How to use with the Acme boards | Product description |
|
| 1-wire Dallas DS18B20 thermal sensor | 5,00 |
EPS EUR 12.00
| EPS - Extended Power Supply module EPS is a DC-DC converter with an input range of 7 to 28 Volt DC output 5 Volt DC @ 2A.
| Product description | |
| Extended Power Supply module | 12,00 |
ETHCON-1 EUR 2.00
| ETHCON-1 - RJ45 LAN Transformer Ethernet 10/100 Base-T connector RJ45 LAN Transformer Ethernet 10/100 Base-T connector
|
| RJ45 LAN Transformer Ethernet 10/100 Base-T connector | 2,00 |
FC-3754-1M EUR 1.00
| FC-3754-1M - 1 meter of 10 wires flat cable for Daisy wiring 1 meter of grey conductor flat cable, .025" pitch, 10 wires at 30 AWG, to use for Daisy wiring.
| 3M Datasheet |
|
| 1 meter of 10 wires flat cable for Daisy wiring | 1,00 |
FLAT-20CM EUR 2.00
| FLAT-20CM - Flat cable 10 wires, 20 cm, pitch 1.27 mm Ribbon cable for YARM-DEV or DAISY modules wiring:
- Length 20 cm
- 10 wires
- Pitch 1.27 mm
|
| Flat cable 10 wires, 20 cm, pitch 1.27 mm | 2,00 |
FOXCASE EUR 6.00
| FOXCASE - Plastic enclosure for the FOX Board G20 - Transparent FOXCASE is a transparent plastic enclosure for the FOX Board G20.
| Product description | |
| Plastic enclosure for the FOX Board G20 - Transparent | 6,00 |
FOXCASE-B EUR 6.00
| FOXCASE-B - Plastic enclosure for the FOX Board G20 - Black FOXCASE is a black plastic enclosure for the FOX Board G20.
| Product description | |
| Plastic enclosure for the FOX Board G20 - Black | 6,00 |
FOXG20 EUR 139.00
| FOXG20 - FOX Board G20 FOX Board G20 is a "ready-to-run" Embedded Linux System perfect to use as a solid state WEB server or as a core engine for your embedded appliances.
A fully Open Source environment is available to customize and build your own kernel image or to develop user applications using standard GNU tools. Version with Atmel AT91SAM9G20 with 256KB of FLASH memory, 64MB of RAM and up to 16GB of microSD.
FOXG20 needs some extra accessories in order to be operative:
- a bootable microSD with Linux OS (see DEBM2G or DEBM4G products)
- a 5 Volt DC power source (see PS5V1A product)
- a 3V lithium battery for internal RTC circuitry (see CH23-1220 product)
An evalution kit with all the accessories you need to get started with FOX Board G20 is available on-line on this link: COMBO-2.
Please note
Currently the FOX board G20 are shipped without the daisy connector mounted on top. If you need these connector please ask.
| Product description | |
| FOX Board G20 | 139,00 |
FOXLX832 EUR 159.00
| FOXLX832 - FOX Board LX832 Historical FOX Board version based on Axis Communications ETRAX 100LX microprocessor. The available quantity depends
on how many chips are still available in the end-of-life products market.
Please note:
- this is a brand new board built in Acme Systems during this year (2013) and not an used part so it is covered by a one year warranty (Terms & Conditions)
- don't use this product for new design because we can't ensure product continuity
OBSOLETE PRODUCT: This product is still available
just for the customers who are still using it their products and
do not need our support. Please note that we are not able
to provide technical support on this board.
| Product description || Documentation | |
| FOX Board LX832 | 159,00 |
FPC-40B EUR 0.80
| FPC-40B - Connector FPC 40 pins. Bottom contacts FPC connector at 40 pins. Bottom contacts for
|
| Connector FPC 40 pins. Bottom contacts | 0,80 |
GPSANT EUR 6.00
| GPSANT - GPS active antenna GPS active antenna with SMA male connector to use Daisy-7 add-on board.
|
| GPS active antenna | 6,00 |
HAT-A3-M EUR 29.00
| HAT-A3-M - Led RGB controller for Raspberry Pi 3 - Mounted version Hat A3 is the Acme Systems commercial version of the Active-3 board designed by Henner Zeller to controll RGB led display with Raspberry Pi 3
| Product description | |
| Led RGB controller for Raspberry Pi 3 - Mounted version | 29,00 |
HDR-15-24 EUR 14.00
| HDR-15-24 - Mean Well DIN Rail Power Supply, 24V DC 630mA Ultra slim 15W DIN rail power supply
- Universal input 85-264 VAC
- No load power consumption < 0.3W
- DC output voltage adjustable
- Protections: short circuit, overload, over voltage
- Led indicator for power on
- Useable to provide power supply to the CM3-Home
| Datasheet | |
| Mean Well DIN Rail Power Supply, 24V DC 630mA | 14,00 |
IDC-FLAT EUR 1.00
| IDC-FLAT - IDC socket 1.27mm for Daisy flat cable IDC connector with 1.27mm spaced dual-row pin headers. The insulation displacement (IDC) contacts on these connectors allow them to be quickly and easily crimped onto FLAT-20CM flat ribbon cable for Daisy cabling system.
This female socket is designed to be connected to the male header on the Daisy modules. A polarizing tab in the middle
ensures the correct orientation.
| Datasheet |
|
| IDC socket 1.27mm for Daisy flat cable | 1,00 |
IDC-PCB EUR 1.00
| IDC-PCB - IDC header 5x2 pin pitch 1.27mm SMT SMT IDC header 10 pin (5x2) pitch 1.27 mm
| Datasheet | Other parts |
|
| IDC header 5x2 pin pitch 1.27mm SMT | 1,00 |
LA-117 EUR 9,000.00
| LA-117 - Mastering EQ LA-117 Studio DMI edition Advanced Modular Stereo Multiband Equalizer and Mid/Side Processor especially designed for mastering and mixing use.
Lead time: 60 working days
| Product info | |
| Mastering EQ LA-117 Studio DMI edition | 9.000,00 |
LA-200-16CH EUR 17,000.00
| LA-200-16CH - Modular Analog Mixer 16 channels Modular Analog Mixer 16 channels
Lead time: 60 working days
| Product description | |
| Modular Analog Mixer 16 channels | 17.000,00 |
LA-200-24CH EUR 22,000.00
| LA-200-24CH - Modular Analog Mixer 24 channels Modular Analog Mixer 24 channels
Lead time: 60 working days
| Product description | |
| Modular Analog Mixer 24 channels | 22.000,00 |
LA-200-32CH EUR 27,000.00
| LA-200-32CH - Modular Analog Mixer 32 channels Modular Analog Mixer 32 channels
Lead time: 60 working days
| Product description | |
| Modular Analog Mixer 32 channels | 27.000,00 |
LA-200-8CH EUR 12,000.00
| LA-200-8CH - Modular Analog Mixer 8 channels Modular Analog Mixer 8 channels
Lead time: 60 working days
| Product description | |
| Modular Analog Mixer 8 channels | 12.000,00 |
LA-88 EUR 890.00
| LA-88 - Line Preamp LA-88 Octopus LA-88 8 Channels Line Preamplifier
Lead time: 60 working days
| Product info | |
| Line Preamp LA-88 | 890,00 |
LA-88-PB EUR 150.00
| LA-88-PB - Balanced XLR 8 in 8 our patchbay for LA-88 Patchbay with balanced XLR connectors for LA-88
- 8 XLR balanced input
- 8 XLR balanced output
- DB25 female connector compatible with standard analog DB25 to DB25 snake cables
DB25 snake cable not included
| Product description | |
| Balanced XLR 8 in 8 our patchbay for LA-88 | 150,00 |
LCD-1-Q-10 EUR 50.00
| LCD-1-Q-10 - Mini size 16x2 characters I2C LCD - 10 pcs Winstar display model WO1602I-TFH-AT#
- Bulk stock of 10 pcs
- Black on white Alphanumeric characters: 16 colums x 2 lines
- Backlight type: LED, White
- LCD mode: FSTN positive
- I2C interface
- Power supply: 3.3 or 5 volt Datasheet
- How to use it
|
| Mini size 16x2 characters I2C LCD - 10 pcs | 50,00 |
LCD-43-RT EUR 26.00
| LCD-43-RT - TFT LCD 4.3 inch with resistive touch for Berta A5 LCD TFT LCD with RGB interface
- Size: 4.3 inch
- Touch: Resistive
- Resolution: 480x272
- Color: 24 bit
Datasheet
|
| TFT LCD 4.3 inch with resistive touch for Berta A5 LCD | 26,00 |
LCD-50-RT EUR 31.00
| LCD-50-RT - TFT LCD 5.0 inch with resistive touch for Berta A5 LCD TFT LCD with RGB interface
- Size: 5.0 inch
- Touch: Resistive
- Resolution: 800x480
- Color: 24 bit
Datasheet
|
| TFT LCD 5.0 inch with resistive touch for Berta A5 LCD | 31,00 |
LCD-70-RT EUR 36.00
| LCD-70-RT - TFT LCD 7.0 inch with resistive touch for Berta A5 LCD TFT LCD with RGB interface
- Size: 7.0 inch
- Touch: Resistive
- Resolution: 800x480
- Color: 24 bit
Datasheet
|
| TFT LCD 7.0 inch with resistive touch for Berta A5 LCD | 36,00 |
LEDRGB-02 | RGB led module 32x32 pixel P6 indoor | 19,00 |
LEDRGB-05 EUR 45.00
| LEDRGB-05 - RGB led module 64x64 pixel P3.91 indoor - 25x25 cm Indoor full color LED module
- 64x64 pixel
- 25x25 cm
- Pitch P3.91
- Indoor
Fully compatible with HAT-A3 adapter for Raspberry PI max 3 modules
| Demo | |
| RGB led module 64x64 pixel P3.91 indoor - 25x25 cm | 45,00 |
LRS-350-5 EUR 34.00
| LRS-350-5 - Mean Well 350W Single Output Switching Power Supply 5 VDC 60A Single Output Power Supply is a single-output enclosed type power supply with 30mm of low profile design
- Output 5 VDC 60A
- AC input range selectable by switch (115-220 VAC)
- Withstands 300VAC surge input for 5 seconds
- Protections
- Short Circuit
- Overload
- Overvoltage
- Over-temperature
- Forced air cooling by built-in DC fan
- Built-in cooling fan on-off control
- 1U low profile
- Withstands 5G vibration test
- No-load power consumption <0.75W
- High operating temperature up to +70°C
- High efficiency, long life, and high-reliability
- 3-year warranty
| Product description | |
| Mean Well 350W Single Output Switching Power Supply 5 VDC 60A | 34,00 |
MICROSD16G-E EUR 22.00
| MICROSD16G-E - SanDisk industrial grade 16GB microSD SanDisk 16GB Industrial grade microSD
| Product description | |
| SanDisk industrial grade 16GB microSD | 22,00 |
MICROSD32G-E EUR 32.00
| MICROSD32G-E - SanDisk industrial grade 32GB microSD SanDisk 32GB Industrial grade microSD
| Product description | |
| SanDisk industrial grade 32GB microSD | 32,00 |
MICROSD8G-E EUR 18.00
| MICROSD8G-E - SanDisk industrial grade 8GB microSD SanDisk 8GB Industrial grade microSD
| Product description | |
| SanDisk industrial grade 8GB microSD | 18,00 |
MSD-HOLDER-1 EUR 1.00
| MSD-HOLDER-1 - Micro SD holder push-push type 1.10mm pitch microSD memory holder push-push type
|
| Micro SD holder push-push type | 1,00 |
MSD-HOLDER-2 EUR 2.00
| MSD-HOLDER-2 - Micro SD holder hinge type 1.10mm pitch microSD memory holder, hinge Type,
|
| Micro SD holder hinge type | 2,00 |
MSD-HOLDER-3 EUR 2.00
| MSD-HOLDER-3 - Micro SD holder vertical type Micro SD holder vertical type
|
| Micro SD holder vertical type | 2,00 |
MWS-01 EUR 0.80
| MWS-01 - WIFI-2 on Arietta G25 Manual soldering of WIFI-2 on the Arietta G25. WIFI-2 module not included.
|
| WIFI-2 on Arietta G25 | 0,80 |
MWS-02 EUR 1.20
| MWS-02 - DPI pin strip on Arietta G25 Manual soldering of DPI pin strip on the Arietta G25 including the DPI connector.
|
| DPI pin strip on Arietta G25 | 1,20 |
MWS-03 EUR 1.60
| MWS-03 - Socket on Arietta G25 J4 top side Manual soldering of a 20x2 pitch 2.54mm female connector on the top side of Arietta G25 including the STRIP-002 connector.
|
| Socket on Arietta G25 J4 top side | 1,60 |
MWS-04 EUR 1.60
| MWS-04 - Socket on Arietta G25 J4 bottom side Manual soldering of a 20x2 pitch 2.54mm female connector on the bottom side of Arietta G25 including the STRIP-002 connector.
|
| Socket on Arietta G25 J4 bottom side | 1,60 |
MWS-05 EUR 1.40
| MWS-05 - Header on Arietta G25 J4 top side Manual soldering of a 20x2 pitch 2.54mm male connector on the top side of Arietta G25 including the STRIP-001 connector.
|
| Header on Arietta G25 J4 top side | 1,40 |
MWS-06 EUR 1.40
| MWS-06 - Header on Arietta G25 J4 bottom side Manual welding of a 20x2 pitch 2.54mm male connector on the bottom side of Arietta G25 including the STRIP-001 connector.
|
| Header on Arietta G25 J4 bottom side | 1,40 |
MWS-07 EUR 2.20
| MWS-07 - 90 degree socket on Arietta G25 J4 top side Manual soldering of a 20x2 pitch 2.54mm 90 degree female connector on the top side of Arietta G25 including the STRIP-006 connector.
|
| 90 degree socket on Arietta G25 J4 top side | 2,20 |
MWS-08 EUR 1.60
| MWS-08 - 90 degree header on Arietta G25 J4 top side Manual soldering of a 20x2 pitch 2.54mm 90 degree male connector on the top side of Arietta G25 including the STRIP-005 connector.
|
| 90 degree header on Arietta G25 J4 top side | 1,60 |
MWS-10 EUR 1.00
| MWS-10 - Metallic open frame on Acqua SOM Manual soldering of Metallic open frame on Acqua A5 SOM.
| Product description | |
| Metallic open frame on Acqua SOM | 1,00 |
N60SH EUR 2.00
| N60SH - Female and Male connectors pair
- Pair of connector for Netus G20
- 1 Female and 1 Male connector
- 60 pin pitch 0.8mm pitch
|
| Female and Male connectors pair | 2,00 |
NETUSG20-L EUR 65.00
| NETUSG20-L - ATMEL AT91SAM9G20 CPU module (256KB) Netus G20 is a 4x4cm Linux ready core engine based on the new ARM9 (c) CPU Atmel (tm) AT91SAM9G20 @ 400Mhz designed to reduce the time to market your Linux embedded projects.
- 256KB of flash memory
- 64MB of RAM
Currently the Netus G20 boards are shipped without the connector mounted on top. If you need these connector please ask.
Please note
Currently the Netus G20 boards are shipped without the daisy connector mounted on top. If you need these connector please ask.
| Product description | |
| ATMEL AT91SAM9G20 CPU module (256KB) | 65,00 |
NETUSPS1 EUR 10.00
| NETUSPS1 - Quad power supply module Power supply module that meets all the AT91SAM9G20 CPU power requirements and power-up and power-down sequences to guarantee reliable operations.
| Product description | |
| Quad power supply module | 10,00 |
PH-1704853 EUR 0.80
| PH-1704853 - Phoenix Contact plug for CM3-PANEL-7-POE SL Connector 2 Position Plug, Female Sockets Board to Cable/Wire 0.098" (2.50mm) Spring-Cage
| Datasheet | |
| Phoenix Contact plug for CM3-PANEL-7-POE | 0,80 |
PROTO-2 EUR 1.50
| PROTO-2 - EUROCARD size proto-board SURPLUS SALE
Prototyping board for FOX Board G20, FOX Board LX and Colibri.
Size: 160x100 mm (Eurocard)
Pitch: 2.54mm
|
| EUROCARD size proto-board | 1,50 |
PS-5V1A-EU-MUSB EUR 4.00
| PS-5V1A-EU-MUSB - Switching power supply with UE AC Plug and mini USB DC plug Switching power supply for PS3V3 DC/DC converter module:
- Input 100-240VAC 50/60Hz
- Output 5VDC/1A
- Pluggable directly to the Berta Board or PS3V3
|
| Switching power supply with UE AC Plug and mini USB DC plug | 4,00 |
PS12V2A-EU EUR 15.00
| PS12V2A-EU - Switching wall mount power supply Switching wall mount power supply 12V 2A with european plug for:
| Datasheet | |
| Switching wall mount power supply | 15,00 |
PS5V1A-EU EUR 9.00
| PS5V1A-EU - Switching power supply 5V 1A with european plug Features:
- European AC input: 100-240VAC 50/60Hz 0.2A
- DC output: 2 USB power out plug.
- Output 1: 5VDC/500mA
- Output 2: 5VDC/500mA
- Pluggable directly to the FOX Board with the included USB to 3.5 DC cable
|
| Switching power supply 5V 1A with european plug | 9,00 |
PS5V1A-USB2 EUR 8.00
| PS5V1A-USB2 - Switching power supply 5V 1A - 2 USB out Features:
- European AC input: 100-240VAC 50/60Hz 0.2A
- DC output: 2 USB power out plug.
- Output 1: 5VDC/500mA
- Output 2: 5VDC/500mA
- A microUSB cable (code CABLE-02) is request for Arietta G25
|
| Switching power supply 5V 1A - 2 USB out | 8,00 |
PS5V1AUS EUR 1.00
| PS5V1AUS - Switching power supply with US AC Plug SURPLUS SALE
Switching power supply for FOX Board G20 with AC plug for US
- Input 100-240VAC 50/60Hz
- Output 5VDC/1A
- Pluggable directly to the FOX Board LX or G20
Provided with US AC plug
| Datasheet | |
| Switching power supply with US AC Plug | 1,00 |
R-DESK-16G-EP EUR 24.00
| R-DESK-16G-EP - Raspbian Desktop 16GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Desktop configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Desktop 16GB MicroSD for CM3-Panel | 24,00 |
R-DESK-32G-EP EUR 34.00
| R-DESK-32G-EP - Raspbian Desktop 32GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Desktop already configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Desktop 32GB MicroSD for CM3-Panel | 34,00 |
R-DESK-8G-EP EUR 20.00
| R-DESK-8G-EP - Raspbian Desktop 8GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Desktop already configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Desktop 8GB MicroSD for CM3-Panel | 20,00 |
R-LITE-16G-EP EUR 24.00
| R-LITE-16G-EP - Raspbian Lite 16GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Lite already configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Lite 16GB MicroSD for CM3-Panel | 24,00 |
R-LITE-32G-EP EUR 34.00
| R-LITE-32G-EP - Raspbian Lite 32GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Lite already configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Lite 32GB MicroSD for CM3-Panel | 34,00 |
R-LITE-8G-EP EUR 20.00
| R-LITE-8G-EP - Raspbian Lite 8GB MicroSD for CM3-Panel Ready to use microSD with preinstalled Raspbian Lite already configured to work with the CM3-Panel
Please note that this card contains Open Source code under GPL license and you are buying just the memory card not the software on it. Any rights to this software or support are not included.
| CM3-Panel | |
| Raspbian Lite 8GB MicroSD for CM3-Panel | 20,00 |
ROADRUNNER-Q128 EUR 42.00
| ROADRUNNER-Q128 - SAMA5D27 System on module (128MB) RoadRunner D2 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D27 MPU
- 256 MByte of DDR3 RAM
- 128MB of QuadSPI on-board
- Extended temperature range (-40° +85°)
| Product description | |
| SAMA5D27 System on module (128MB) | 42,00 |
ROADRUNNER-Q16 EUR 36.00
| ROADRUNNER-Q16 - SAMA5D27 System on module (16MB) RoadRunner D2 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D27 MPU
- 256 MByte of DDR3 RAM
- 16MB of QuadSPI on-board
- Extended temperature range (-40° +85°)
| Product description | |
| SAMA5D27 System on module (16MB) | 36,00 |
ROADRUNNER-Q64 EUR 38.00
| ROADRUNNER-Q64 - SAMA5D27 System on module (64MB) RoadRunner D2 is a small and low-cost Linux embedded system on chip
- Atmel SAMA5D27 MPU
- 256 MByte of DDR3 RAM
- 64MB of QuadSPI on-board
- Extended temperature range (-40° +85°)
| Product description | |
| SAMA5D27 System on module (64MB) | 38,00 |
SD-HOLDER-1 EUR 1.50
| SD-HOLDER-1 - Simple SD holder Simple holder for SD card
|
| Simple SD holder | 1,50 |
SHIELD-1 EUR 15.00
| SHIELD-1 - Metallic frame and cover for Acqua board Wurth Elektronik metallic frame to be welded on the Aria A5 SoM in case of use in EMI noise environment (for example near DC motors).
This shield is composed by two parts:
- a metallic open frame to weld to the board
- a removable metallic cover
|
| Metallic frame and cover for Acqua board | 15,00 |
STRIP-001-Q10 EUR 6.00
| STRIP-001-Q10 - Male strip 20x2 pin pitch 2.54mm (q.ty 10)
- Male strip
- 20x2 pin
- Pitch 2.54mm (100mils)
- Pin lenght 6mm
- Q.ty 10 pcs
|
| Male strip 20x2 pin pitch 2.54mm (q.ty 10) | 6,00 |
STRIP-002-Q10 EUR 8.00
| STRIP-002-Q10 - Female strip 20x2 pin pitch 2.54mm (q.ty 10)
- Female strip
- 20x2 pin
- Pitch 2.54mm (100mils)
- Q.ty 10 pcs
|
| Female strip 20x2 pin pitch 2.54mm (q.ty 10) | 8,00 |
STRIP-003 EUR 0.60
| STRIP-003 - Male strip 25x2 pin pitch 1.27mm
- Male strip
- 25x2 pin
- Pitch 1.27mm (50mils)
- Compatible with Acqua module
|
| Male strip 25x2 pin pitch 1.27mm | 0,60 |
STRIP-003-REEL-800 EUR 392.00
| STRIP-003-REEL-800 - Reel (800 pcs) of male strip 25x2 pin pitch 1.27mm
- Male strip
- 800 pcs
- Ready for pick and place
- 25x2 pin
- Pitch 1.27mm (50mils)
- Compatible with Acqua module
|
| Reel (800 pcs) of male strip 25x2 pin pitch 1.27mm | 392,00 |
STRIP-004 EUR 0.80
| STRIP-004 - Female strip 25x2 pin pitch 1.27mm
- Female strip
- 25x2 pin
- Pitch 1.27mm (50mils)
|
| Female strip 25x2 pin pitch 1.27mm | 0,80 |
STRIP-005 EUR 0.80
| STRIP-005 - Male strip 20x2 pin 90 degree pitch 2.54mm
- Male strip
- 20x2 pin 90 degree
- Pitch 2.54mm (100mils)
|
| Male strip 20x2 pin 90 degree pitch 2.54mm | 0,80 |
STRIP-006 EUR 1.40
| STRIP-006 - Female strip 20x2 pin 90 degree pitch 2.54mm
- Female strip
- 20x2 pin 90 degree
- Pitch 2.54mm (100mils)
|
| Female strip 20x2 pin 90 degree pitch 2.54mm | 1,40 |
STRIP-007 EUR 0.80
| STRIP-007 - Male strip 20x2 pins pitch 2.54mm len 12mm
- Male strips
- 20x2 pin
- Pitch 2.54mm
- Lenght 12mm
|
| Male strip 20x2 pins pitch 2.54mm len 12mm | 0,80 |
STRIP-008 EUR 0.40
| STRIP-008 - 6 pin male strip for debug port Male 6 pin strip ptch 2.54 mm (100 mils) for the Arietta G25 debug port
|
| 6 pin male strip for debug port | 0,40 |
STRIP-009 EUR 0.30
| STRIP-009 - Male strip 14 pin pitch 2.54mm Male strip
- 14 pin
- Pitch 2.54mm (100mils)
- Pin lenght 6mm
- Compatible with YARM-DEV module
|
| Male strip 14 pin pitch 2.54mm | 0,30 |
STRIP-010 EUR 0.40
| STRIP-010 - Female strip 14 pin pitch 2.54mm Female strip
- 14 pin
- Pitch 2.54mm (100mils)
- Compatible with YARM-DEV module
|
| Female strip 14 pin pitch 2.54mm | 0,40 |
STRIP-011 EUR 0.20
| STRIP-011 - Male strip 7x1 pin pitch 2mm Male strip 7x1 pin pitch 2mm
- Male strip
- 7x1 pin
- Pitch 2mm
- Used on WIFI-2 module
|
| Male strip 7x1 pin pitch 2mm | 0,20 |
STRIP-012 EUR 0.30
| STRIP-012 - Female strip 7x1 pin pitch 2mm Female 7x1 pin pitch 2mm
- Female strip
- 7x1 pin
- Pitch 2mm
- Compatible with WIFI-2 module
|
| Female strip 7x1 pin pitch 2mm | 0,30 |
TUXCASE EUR 28.00
| TUXCASE - TUX Case Plastic puppet that resembles the very popular Linux icon TUX drawn by Larry Ewing.
Actually it is the case for the old FOX Board G20.
|
| TUX Case | 28,00 |
USB-3V-SER EUR 8.00
| USB-3V-SER - USB to 3V3 serial converter USB to 3V3 serial converter ad 3.3 volt with separated pin plugs
| Product description | |
| USB to 3V3 serial converter | 8,00 |
USBCON-1 EUR 1.00
| USBCON-1 - USB host connector USB A host connector
|
| USB host connector | 1,00 |
USBCON-2 EUR 2.00
| USBCON-2 - Double USB host A connector Double USB host A connector
|
| Double USB host A connector | 2,00 |
WIFI-2 EUR 7.00
| WIFI-2 - WiFi USB module OEM Small USB 2.0 IEEE 802.11 b/g/n Wi-Fi compliant module based on the RaLink RT5370N chip. It works at 3.3V and can be configured also in Access Point mode.
This model requires an external antenna model AN-WIFI-01 or AN-WIFI-02.
| Product description || Datasheet | |
| WiFi USB module | 7,00 |
WIFI-2-IA EUR 7.00
| WIFI-2-IA - WiFi USB module (Internal Antenna) OEM Small USB 2.0 IEEE 802.11 b/g/n Wi-Fi compliant module based on the RaLink RT5370N chip. It works at 3.3V and can be configured also in Access Point mode.
This model uses the internal PCB antenna. The operative range of this solution is limited to few meters. If you need a greater distance evaluate the model with external antenna.
Don't use the WIFI-2-IA model with Arietta G25 board because it hangs the CPU. Use the WIFI-2 instead
| Product description || Datasheet | |
| WiFi USB module (Internal Antenna) | 7,00 |
WIFI-3 EUR 12.00
| WIFI-3 - Mini USB WiFi adapter 5.8GHz-2.4GHz Mini USB Wireless Adapter
- 5.8GHz - 2.4 GHz
- Support 802.11ac standard WiFi
- Compatible with 802.11b/g/n wireless devices
- High wireless transmission rate, dual band (2.4GHz/150Mpbs 5.8GHz/433Mbps)
- Support WPA/WPA2/WEP/802.1X/WMM data encryption
- Compatible with Raspberry Pi and all the Acme Systems Linux boards
- Compatible with Windows, Linux and MAC OS X PC
- Strong anti-interference ability
- Internal antenna
- Total size: 30x13x7 mm
- Length out USB port: 16mm
| How to use it on Linux | |
| Mini USB WiFi adapter 5.8GHz-2.4GHz | 12,00 |
XTERM-01 EUR 25.00
| XTERM-01 - 2.8 inch TFT display with resistive touch for Arietta G25
- 2.8 inch TFT display
- Resistive touch screen
- USB host port
Arietta G25 not included
| Product description | |
| 2.8 inch TFT display with resistive touch for Arietta G25 | 25,00 |
YARM EUR 8.90
| YARM - ISM 868 MHz radio module ISM 868 MHz RF radio module with
- Low power Atmel SAML21 MCU (ARM Cortex M0+ @ 48MHz)
- 32KByte of RAM memory
- 256KByte of FLASH memory
- Atmel ATA8510 Monolithic RF Transceiver IC for Sub-1GHz smart RF applications
| Product description ||
Flat price up to 999 pcs | |
| ISM 868 MHz radio module | 8,90 |
YARM-2-ICE EUR 9.00
| YARM-2-ICE - Yarm-dev to Atmel ICE adapter Adapter to connect YARM-DEV to the ATMEL-ICE-BASIC programmer.
Three FLAT-20 flat cables are required to connect the YARM-DEV to the Atmel ICE programmer
| Yarm radio module | |
| Yarm-dev to Atmel ICE adapter | 9,00 |
YARM-ANT-01 EUR 12.00
| YARM-ANT-01 - Antenna with cable Antenna stick for YARM-DEV with uFL to SMA cable
- Rubber antenna with FEMALE SMA connector
- RF cable with panel mountable MALE SMA connector
| Yarm radio module | |
| Antenna with cable | 12,00 |
YARM-DEV EUR 18.00
| YARM-DEV - Evaluation board for YARM module Carrier board for a rapid evaluation of the YARM radio module cababilities.
In includes the following parts:
- MicroUSB port for power and data
- ICP programmer port input
- Double line of 14 pin pitch 2.54 mm for prototyping
| Product description ||
Flat price up to 999 pcs | |
| Evaluation board for YARM module | 18,00 |
YARM-DEV-ICP EUR 119.00
| YARM-DEV-ICP - Jtag programmer for YARM-DEV This kit includes
- 1 Atmel ICE basic JTAG programmer/debugger
- 1 YARM-2-ICE adapter
- 3 Flat cables
| How to use it | |
| Jtag programmer for YARM-DEV | 119,00 |